Toyota Corolla Bumper Covers

• The bumper cover is a fitting that covers the car’s crash safety components and the actual bumper.
• The bumper cover’s job is to crumple and slow down the transfer of energy to the bumper bar and bumper reinforcement bar.
• Toyota Corolla bumper covers are typically priced anywhere between $160 and $680.
• Any existing damage on your bumper cover may affect the panel’s ability to absorb and dissipate the kinetic energy of a crash.
• Whether it’s about preserving your Toyota Corrola’s resale value or safety-wise, replacing your damaged bumper cover is very important. 

 

For over five decades, consumers around the world have loved the Toyota Corolla dearly. Since its 1966 introduction, Toyota has sold more than 40 million units of the compact vehicle. It easily earned the reputation of being the best-selling nameplate not only in the United States but also in the world. The Corolla was originally a subcompact, rear-wheel drive car back in the days. Now, Toyota markets it as a compact sedan and hatchback, going up against the likes of the Honda Civic.

 

One component that makes the Toyota Corolla both safe and good-looking is its bumper cover. Let’s take a closer look at it to understand Toyota’s most successful nameplate in history.

 

The bumper cover is a fitting that covers the car’s crash safety components and the actual bumper. It is usually made of high-grade, high-density reinforced plastic and is attached to the bumper bar and bumper reinforcement bar by bumper brackets. The Toyota Corolla has front and rear bumper covers that protect front and rear components like headlights, grille, fog lights, and tail lights.

 

Bumpers were originally designed to resist and repel the brunt of collision impact. This is why older bumper covers were typically made of steel. However, this resulted in more injuries than manufacturers expected to avoid. This pushed manufacturers to find a better alternative, ultimately reversing its function.

 

Instead of repelling the force, manufacturers found out that the bumper should have an extra layer that would absorb force and slow it down before reaching the actual metal beam. This idea led to the production of the high-strength plastic exterior panels that we now refer to as bumper covers.

 

The bumper cover fits on top of the bumper bar, which is attached to the bumper reinforcement bar. The bumper bar is a metal beam that receives much of the impact’s kinetic energy in low-speed collisions. 

 

The bumper cover’s job is to break and slow down the transfer of energy to the bumper bar and bumper reinforcement bar. It achieves this by crumpling upon impact. Aside from this, the bumper cover protects internal components from small rocks and other road debris while you’re cruising on the highway.

 

The Toyota Corolla has had 12 generations in total and each generation is uniquely designed. If you’re in the market for a specific Toyota Corolla bumper cover, finding the right part may take some time. To help narrow down your search, indicate the year, make, and model of your car on the search filter tab.

 

Toyota Corolla bumper covers are typically priced anywhere between $160 and $680. The price range includes individually sold products, as well as kits, and sets of two. If you want guaranteed quality, there are CAPA-certified Toyota Corolla bumper covers in the catalog. All products are made of high-strength plastic, primed and ready to be painted.

 

Any existing damage on your bumper cover affects the panel’s ability to absorb and dissipate the kinetic energy of a crash. Here are some reasons why replacing your damaged bumper cover is important.

Keeps your Toyota Tacoma looking fresh

If you want to maintain your truck’s appeal, it would be a great idea to replace any panel with evident damage and deterioration. By doing this, you’re also preserving your vehicle’s resale value. 
Make sure you pay attention to any signs of cracking on the surface and mounting provision. Any cosmetic damage can turn potential buyers away from purchasing your Toyota Corolla.

 

Prevents serious injury in a subsequent crash

A damaged bumper cover could potentially affect headlight, radiator, fog light, and tail light mounting. A loose component could cause clunking noises and riding discomfort. More safety problems may arise if you ignore a failing bumper cover. Make sure you consult your trusted mechanic as soon as you notice damage on your bumper cover.

 

Discover early signs of internal damage

By letting your mechanic check the bumper cover thoroughly, you’ll have an increased chance of preventing any existing internal damage from getting worse. Replacing the bumper cover is a perfect opportunity to evaluate all surrounding components. This way, your mechanic would be able to tell if there are internal components affected.
 

Just like the body and the fenders of your car, the Toyota Corolla bumper covers have to be kept clean and maintained properly to achieve that brand-new look each time your vehicle is on the road. However, since the bumpers are located on the outside of your car, dirt and grime from the polluted air can stick and accumulate on the surface of the bumper covers if they're not cleaned regularly. You can follow the simple cleaning tips listed below, as well as some useful hints on how to keep your bumper covers in good shape.

 

Wash your car's bumper covers on a regular basis.

 

 

Washing your Toyota Corolla bumper covers is an easy task which only requires simple materials such as automotive soap, soft sponge, and water. You can also use undiluted white vinegar to remove spots or mineral deposits on the bumper covers' surface. However, if dirt has stuck on the bumpers' surface and become difficult to remove even after washing it, you can use a soft bristle brush to scrub the plastic bumpers. You have to scrub it gently in a circular motion to avoid marks on the surface.

 

 

Restore the areas of the bumper cover that have faded.

 

 

Aside from your car's old age, another reason why the paint on your car's bumper cover fades is the sun's UV rays. Its harmful effects cause the paint to look dull and worn out. To make the bumper cover look bright once again, you have to restore it by buffing the faded areas. You can use a soft cotton towel on the portions that the buffer can't reach. To achieve a glossy and shiny finish, you can apply car polish after you have buffed the faded portions of the bumper cover.

 

 

Remove the Toyota Corolla bumper covers properly.

 

 

When you need to remove the bumper covers of your Toyota Corolla, make sure that you do the proper way to avoid damaging the plastic bumper covers. It is important that you have the right tools before you begin removing them. A floor jack and jack stands can make the work easier by giving you more room to move since you'll need to remove the screws and bolts underneath your car. You should support the bumper cover while you're detaching it and don't just let it dangle or drop unevenly.

 

Maintenance and Care Tips to Keep your Toyota Corolla Bumper Cover in Top Shape

The Toyota Corolla has been a favorite economic sedan in the American market. The Japanese automaker offers affordable parts and components for it to keep your car running properly. Likewise, you also benefit from having a simple yet tasteful design from years of crafting the Toyota design language. You just got to love the lines and aesthetic cues put into the car. This is the case with the Toyota Corolla bumper cover. For years, this is one panel that exemplifies the Japanese engineers' dedication in producing a capable vehicle worthy of performance, aesthetic appeal, and safety. As the bumper cover is designed to make your Corolla look better and safer, you should not forget to take care of it to preserve its integrity. Here are some care tips that you should apply to your Toyota Corolla bumper cover.

• Regularly inspect the integrity of your bumper cover.

Aesthetics aside, the main purpose of having your Toyota Corolla bumper cover is to protect you and your car from collisions. No matter how hard or light the collision is, you should be diligent enough to inspect the bumper's integrity. Check for misalignments, dangling parts, and loose bolts. After identifying the issues, you should address them accordingly. Make sure you use the correct parts when you do so.

• Wash the surface of your bumper cover with water.

Water is a very helpful substance when cleaning any exterior panel of your Toyota Corolla. You should also maximize it when you clean your Toyota Corolla bumper cover. Direct your hose to the bumper at an angle as you start rinsing. This should take care of the light dust build-up on the surface. It should also loosen any particles that might have been stuck along the crevices of the panel. After the water treatment, the bumper should be ready for wiping or scrubbing, depending on how dirty it is.

• Scrub the surface of the bumper cover to further clean its surface.

Further clean your bumper cover by gently scrubbing it with a sponge or wash mitt. Use it along with your favorite car shampoo. It should give back the luster to your bumper cover.

Driving out with your Toyota Corolla is a splendid idea. It feels good driving it through the highway and even through the busy streets. For tonight, you take it out for your regular visit to your favorite local diner. As you are enjoying your milkshake, fries, and burger, you did not know that an unsuspecting driver backed into your car and damaged your Toyota Corolla bumper cover. That is a real bummer, especially after chomping down on your favorite diner combo. Unfortunately, the bumper can't be hammered back to shape just like those of the old cars. So you will just have to replace it with a new one. Here are some installation tips for your Toyota Corolla bumper cover.

Tip #1: Be specific with the bumper cover you are getting for your Toyota Corolla.

Are you getting an OEM bumper cover or an aftermarket version of it? What year and model is your Toyota Corolla? Those are the questions that you have to consider first when you are about to get the replacement bumper cover for your Toyota Corolla. You have to be very specific with the details so you can avoid any mismatch with mounting points, alignment, and sockets.

Tip #2: Get someone to help you with the installation.

Mounting and dismounting bumpers can be a tricky job if you go solo. We advise you tag along another car guy to help you out with your installation feat. That person can help you support the bumper as you work on it and can also provide you a second opinion. Hey, maybe after that, you two can go grab some burger and milkshake.

Tip #3: Evaluate your Toyota Corolla's chassis after removing the damaged bumper.

You need to evaluate the condition of your chassis after you remove your old damaged bumper. This will allow you to assess any hidden damage that you might have overlooked when you made your initial inspection of the bumper cover.

Tip #4: Go for a test fit of the bumper cover before locking it to place.

Before you finally commit to the bumper cover you ordered, do a test fit of it on your Corolla. Check if everything is aligned. Once you are convinced, bolt the bumper cover in place.