How to Replace Your Tail Light Assembly

There are several reasons why you may want to replace your entire tail light assembly (not just the bulb). Maybe you got into a fender bender and the lens is broken. Or maybe your tail lights are dingy-looking after years of service and you’re looking to carry out some maintenance work to increase your car’s resale value.

Regardless of why you want to replace your tail light assembly, generally, the procedure is pretty straightforward. On some vehicles, however, the rear bumper cover or interior trim panel must be removed to access the tail light fasteners—and that can make the job more complicated.

What Tools Do You Need to Replace Your Tail Light Assembly?

The tools required to replace a tail light assembly can vary, depending on what type of car you have.

But in general, you’ll need:

• Screwdrivers
• Ratchet, appropriate size sockets and wrenches
• Safety glasses

Should You Do the Job Yourself?

Tail light assembly replacement is typically pretty easy. When it comes to vehicle maintenance, changing out the tail light isn’t always on top of everyone’s priority list. However, when you finally get around to it, you’ll be glad to know that it’s a relatively easy task. Plus, unlike some other tasks like replacing your brakes, vehicle safety is unlikely to be compromised if something goes wrong.

That being said, you could damage your vehicle if the job is done incorrectly. You could also end up wasting a lot of time or even hurt yourself.

So, if you feel like you’re up to the job, go for it. Otherwise, leave it to a professional.

A Step-By-Step Guide to Replacing Your Tail Light Assembly

Now we get to the fun part: tail light assembly replacement. Are you ready to grab some tools and get dirty? Good.

We’re going to discuss replacing a traditional tail light assembly that uses mini bulbs.

Before we start, however, keep in mind that all vehicles are different. Be sure to follow the repair information for your specific application. Repair manuals, such as those from Chilton, are useful, but an ALLDATA subscription is even better. ALLDATA has single-vehicle subscriptions for DIYers that provide detailed factory repair information.

Note: The following are general guidelines for educational and entertainment purposes only. Consult your vehicle’s factory information for specific repair instructions and recommended safety procedures.

How to Remove Tail Light Assembly

1. Put on your safety glasses.
2. Disconnect the negative battery cable.
3. If necessary, remove the rear bumper cover or interior trim panel per the factory repair information. On some vehicles, this must be done to access the tail light assembly retaining fasteners. The process generally involves removing a collection of screws and/or clips to free the bumper or trim panel.
4. Once you have direct access to the tail light assembly, remove the bolts or screws holding it in place.
5. Pull the tail light assembly out and away from the vehicle. Keep in mind: there may still be retainer clips holding the assembly in place. You’ll need to carefully dislodge the assembly from the clips as you pull it toward you.
6. Disconnect the electrical connectors from the back of the assembly.
7. Some replacement tail light assemblies will come with new bulbs. If yours does not, you will need to remove the old bulbs and sockets so they can be reused. Typically, this involves turning the bulb socket counterclockwise to remove it from the tail light assembly.

Check out these videos for tips on how to replace your tail light assembly and bulb:

How to Install Tail Light Assembly

1. Compare the new tail light assembly to the old one to be sure that both are the same design.
2. Reinstall the bulbs and sockets in the tail light assembly as needed.
3. Reconnect the electrical connectors.
4. Mount the tail light assembly in place. Be sure that it slides into any retainer clips affixed to the rear of the vehicle.
5. Reinstall the tail light assembly mounting bolts or nuts and carefully tighten them down until they’re snug. Do not overtighten. If needed, you can consult the factory repair information and use a torque wrench to tighten the fasteners to the manufacturer’s specification.
6. Reinstall the rear bumper or interior trim panel as needed.
7. Reconnect the negative battery cable.

Tail lights and their retaining clips (if applicable) are made of fragile plastic. So, be gentle and take your time when performing the replacement.

Get a Replacement Tail Light Assembly That Fits Your Car

Driving around with a broken tail light is never a good idea, even if it’s taped back together and still emitting a red light. You’re likely to get pulled over and fined. A broken tail light is a safety hazard that can distract drivers behind you and cause an accident. It’s also possible for water to seep through the fractured cover, which can cause a short and lead to more damage. To avoid all this, you’ll have to replace your tail light as soon as possible. Luckily, getting a new tail light assembly is fast and easy with CarParts.com. 

Say goodbye to long wait times when you order a new tail light from CarParts.com. Thanks to our strategically located warehouses, you can expect to receive your new tail light in as fast as two business days. Just be sure to order by 12 p.m. ET. We also offer round-the-clock support, so you can reach out to our friendly customer service staff for any help you might need. 

Don’t let your faulty tail light put you at risk. Check out our wide selection of high-quality tail lights at CarParts.com today.

Products Mentioned in this Guide