How To Replace Leaf Spring Bushings

Bushings are found throughout a vehicle’s suspension. They act like a joint that connects two load-bearing components.

A bushing is a cylindrical component that’s composed of a small inner sleeve and a larger outer shell. Between these two cylindrical parts is an elastomer that’s made from a soft material like rubber or polyurethane.

As the vehicle ages, the soft material inside the bushing deteriorates, creating play or “slop” between the inner sleeve and outer shell. These can cause symptoms such as squeaking or clunking sounds. In severe cases, the leaf spring can get misaligned. In this article, we’ll tackle the leaf spring bushing’s importance and how to replace it once it wears out.

What Are Leaf Spring Bushings?

The leaf spring bushing is typically an inner and outer shell with rubber bonded to both shells. When the rubber bond is broken between the rubber and either shell, the rubber will squeak as suspension angles change. Sometimes this happens because the bushing through bolts just needs to be torqued.

The leaf spring bushing is typically an inner and outer shell with rubber bonded to both shells.

– Richard McCuistian, ASE Certified Master Automobile Technician

In a leaf spring bushing, the leaf spring wraps around the outer shell, while a bolt is inserted through the inner sleeve.

The bolt that goes through the inner sleeve also goes through a part called a shackle, which connects the leaf spring assembly to the vehicle’s chassis.

The soft material inside bushings allows them to act like a cushion between the two metal components, effectively reducing vibrations and dampening noise. Bushings can also twist, allowing the shackle and leaf spring to move whenever a load is applied to the vehicle.

Tips and Tricks for Leaf Spring Bushing Replacement

Tool Options

• You can use various tools for leaf spring bushing replacement. These include an impact gun, a saw, a hammer, or a chisel.

Vehicle Elevation

• When raising the rear of the vehicle using a jack, make sure you raise it from the rear axle or third member. This will allow you to lower the vehicle onto jack stands, but the jack stands need to be under the frame rather than the axle. The leaf springs don’t need to be loaded during this procedure.
• To prevent the leaf springs and suspension components from falling when you’re removing the bolts that pass through the bushings, you need to prop the suspension up from the third member using a jack. Keep in mind that your vehicle should already be resting on jack stands at this point.

Bushing Removal

• You should remove leaf spring bolts one end at a time to prevent the suspension assembly from moving out of place.
• Using an impact wrench can make the task of removing bushing bolts easier, as the bolts tend to corrode and seize because they’re constantly exposed to dirt and moisture.
• Applying a rust penetrant can ease the bushing removal process, especially if you’re using elbow grease and manual tools like a ball joint press, hammer, chisel, or saw.

Installing a New Bushing

• Greasing the area where the new bushing will sit is beneficial, as it’ll allow the new bushing to slide in more easily.
• Using tools like a C-clamp or ball-joint press can allow you to slide the new bushing easily.
• Coating the inside of the bushing with anti-seize or grease will add some rust protection and future service might be easier.

Reattaching Leaf Spring

• When it comes to reattaching the leaf spring to your vehicle’s chassis, sometimes you just need to slide the shackles onto the bushing, insert the washer, and secure it with a bolt. However, the attachment process can vary between vehicles.
• When tightening the bushing bolt, make sure that you don’t tighten it immediately.

Final Steps

• You can only fully tighten the bushing bolts according to the recommended specifications once the vehicle is resting on its suspension.

Considerations for Home Mechanics

• If you’ve observed that your vehicle’s leaf spring shackles are also rusted, then you should replace them because the rust can threaten the suspension’s structural integrity.

By following these tips and tricks, you can properly replace leaf spring bushings and maintain your vehicle’s suspension system.

Why You Should Replace Your Vehicle’s Leaf Spring Bushing

Worn-out bushings won’t just create unwanted noise, they can also leave your suspension and tires misaligned, and even make your vehicle unstable. For your safety, it’s best that you replace any worn-out leaf spring bushings before they fail.

Where to Get High-Quality Leaf Spring Bushings for Your Vehicle

Speaking of replacing worn-out leaf spring bushings, you should get high-quality parts to get the most out of your money. Lucky for you, CarParts.com has you covered with OE-grade replacements.

To start shopping, enter your ride’s year, make, and model into our vehicle selector to view direct-fit replacement parts for your daily driver. You can also use the search filters to find products according to your preferred brand, price range, quantity, and more.

All our products passed strict quality checks to ensure that they can withstand tough operating environments and extreme temperatures. Order now, and check out securely in a matter of minutes.

Never worry about going over budget when you shop from us. All our products come with a low-price and lifetime replacement guarantee, helping you get the best value for your money.

Thanks to our strategically located warehouses across the US, you can get the parts you need delivered straight to your doorstep in as fast as two business days.

Shop at CarParts.com today to get high-quality replacement leaf spring bushings!